When you’re mowing your lawn as usual, but then something goes wrong. Your mower is now stuck in reverse and won’t move forward again. What you see next are blades spinning faster and faster until the engine roars like crazy and sparks shoot out from somewhere above or below the spinning blades.

Fortunately, there are a few things you can check to disable the reverse safety switch on the Craftsman mower so that it moves forward again. Here we will provide you with a full guide on how you can disable the reserve safety switch on the Craftsman mower.

What is a reverse safety switch?

A reverse safety switch is a safety mechanism that prevents you from starting your mower in the wrong direction. If you mistakenly start the engine in reverse, the switch immediately stops the engine so that you don’t risk injury or damage to your mower. 

If the mower is equipped with a shaft-mounted handle, this is the most likely switch to be used as a reverse safety. A reverse safety switch can either be on the engine itself or the transmission. It is important to know where your reverse safety switch is to avoid accidentally engaging it.

Where you can find the reverse safety switch on the mower?

Reverse safety switches can be found on the engine, on the transmission, or on the handle. On the engine, it is typically a wire or a button. On the transmission, a button or a mechanism. On the handle, a button or a lever.

For example, if your mower has a shaft-mounted handle, and you see a small wire that is connected to the handle that is the reverse safety switch. If the shaft-mounted handle has a button that is the reverse safety switch.

If the shaft-mounted handle has a bar with a button on one end and a lever on the other end, the button is the reverse safety switch.

How to disable the reverse safety switch on the Craftsman mower, step by step

  • Disconnect the battery
  • Remove the back panel
  • Remove the safety switch screw
  • Reassemble

How to Disable the Reverse Safety Switch on the Craftsman Mower?

How to Disable Reverse Safety Switch on Craftsman Mower?

1. Disconnect the battery

If you’re working on your Craftsman lawn mower and need to disable the reverse safety switch, the first step is to disconnect the battery. This will ensure that the lawn mower doesn’t accidentally start while you’re working on it. Once the battery is disconnected, you can proceed with disabling the reverse safety switch.

2. Remove the back panel

To disable the reverse safety switch on a Craftsman lawn mower, you’ll need to remove the back panel. This will give you access to the switch itself. Once the panel is off, locate the switch and flip it to the “off” position.

3. Remove the safety switch screw

If you’re having trouble with your Craftsman lawn mower, you may need to disable the reverse safety switch. Here’s a step-by-step guide on how to do it.

  1. Locate the safety switch. On most Craftsman lawnmowers, the safety switch is located near the handle.
  2. Remove the safety switch screw. This will allow you to remove the switch itself.
  3. Disconnect the wiring from the switch. There are usually two wires connected to the switch. One will be black and one will be white.
  4. Reconnect the wiring to the switch in the reverse order. Make sure that the black wire is connected to the terminal marked “B” and the white wire is connected to the terminal marked “W”.
  5. Replace the safety switch screw and tighten it securely.

Now your Craftsman lawn mower should be able to operate in reverse without any problems.

4. Reassemble

Assuming you have followed the steps above, it’s now time to reassemble your lawn mower.

  1. Replace the blade and make sure it is tightened securely.
  2. Reattach the spark plug and reconnect the wire.
  3. Now put the cover back on the engine and screw it in place.

Your lawn mower should now be ready to use without the reverse safety switch.

Also Read: Do You Need Torque Wrench for Lawn Mower Blade?

How do you turn off the reverse safety switch on a Troy Bilt lawn mower?

If your Troy Bilt lawn mower has a reverse safety switch on the shaft-mounted handle, you can turn it off by lifting the handle. Once the handle is lifted, the reverse safety switch will be released, and you can start the mower in any direction.

Alternatively, you can disconnect the wire from the shaft-mounted handle. Once the wire is disconnected, the reverse safety switch is released, and you can start the mower in any direction.

Conclusion:

When you are mowing, it’s important to note the location of the reverse safety switch on your mower so that you don’t accidentally engage it. Some mowers have the reverse safety switch on the engine, some have it on the transmission, and some have it on the shaft-mounted handle.

If you accidentally engage the reverse safety switch, the engine will stop immediately, which can be frustrating.

To prevent this from happening, make sure you know where your reverse safety switch is and keep it in mind while mowing.

When you are mowing, it’s important to note the location of the reverse safety switch on your mower so that you don’t accidentally engage it.

If you accidentally engage the reverse safety switch, the engine will stop immediately. To prevent this from happening, make sure you know where your reverse safety switch is and keep it in mind while mowing.

Source:

Victoria Peterson
Author

I am a passionate gardener who wants to help you create and maintain your dream yard. I know that it can be daunting to take on a project like this, but I am here to help. I have been gardening for years and have learned a lot along the way. I want to share my knowledge with you and help you create the perfect yard for your home.

Write A Comment